This document lists some of the popular modem's startup strings and dip-switch
settings. In order, the modems covered here are:

    - US Robotics HST "Dual Standard"
    - Multitech 224E(h)
    - Hayes 2400
    - Multitech 9600 baud V.32 modem

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

US Robotics HST "Dual Standard"
-------------------------------

The Startup Strings and result codes for this modem is listed in the STARTUP.2
file located on your distribution disk as "\MAGNUM\PGM_DIR\STARTUP.2"

    LARGE switch labeled CTS:  UP

The 10 dipswitches next to that large switch are as follows:

    Switch#      Setting

      1            UP
      2           DOWN
      3           DOWN
      4           DOWN
      5            UP
      6            UP
      7            UP
      8           DOWN
      9           DOWN
     10            UP


- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

MultiTech 224E(h)
-----------------

The Startup Strings and result codes for this modem is listed in the STARTUP.1
file located on your distribution disk as "\MAGNUM\PGM_DIR\STARTUP.1"

The dip-switch settings for this modem are as follows:

The 8-switch block on the bottom of the modem:

    Switch#      Setting

      1            UP
      2           DOWN
      3           DOWN
      4           DOWN
      5           DOWN
      6            UP
      7            UP
      8           DOWN

The 4-switch block on the inside of the modem:

    Switch#      Setting

      1           DOWN
      2            UP
      3           DOWN
      4           DOWN

All jumpers on the inside of the modem (there's 3 of them) should be jumpered
towards the front two pins. The front is the side where the modem lights are.

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Hayes 2400
----------

   BAUDRATE:    2400
   PARITY:      n
   DATABITS:    8
   STOPBITS:    1
   WAITCARRIER: 30
   MODEMRESET:  AT
   STARTUP1:    AT &F&W
   STARTUP2:    AT
   STARTUP3:    AT S10=7E0V0M0Q0&C1&D2S0=1&W
   REINIT:      AT
   DELAY1:      1500
   DELAY2:      1500
   DELAY3:      2500
   DTELOCKED:   n
   ANSWERTYPE:  a
   OPENMODE:    n
   ANSWERCMD:   ATA
   ONHOOK:      ATH0
   OFFHOOK:     ATH1
   ESC_CMDMODE: +++
   ESC_GRDTIM:  700
   GO_ONLINE:   AT O
   END_OFFHOOK: N
   RC_110:
   RC_150:
   RC_300:      1
   RC_600:
   RC_1200:     5
   RC_2400:     10
   RC_4800:
   RC_9600:
   RC_19200:
   ERRORCHECK:  n
   ERC_110:
   ERC_150:
   ERC_300:
   ERC_600:
   ERC_1200:
   ERC_2400:
   ERC_4800:
   ERC_9600:
   ERC_19200:

- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - -

Multitech 9600 baud V.32 modem
-------------------------------------


The dip-switch settings for this modem are as follows:

The 4-switch block:

    Switch#      Setting

      1           DOWN
      2            UP
      3           DOWN
      4           DOWN

The 8-switch block:

    Switch#      Setting

      1            UP
      2           DOWN
      3           DOWN
      4           DOWN
      5            UP
      6            UP
      7            UP
      8           DOWN

Startup Sequences:

   BAUDRATE:    19200
   PARITY:      n
   DATABITS:    8
   STOPBITS:    1
   WAITCARRIER: 30
   MODEMRESET:  AT Z
   STARTUP1:    AT &F
   STARTUP2:    AT E0 &E1 &E4 &E15 $SB19200 $BA0 &R1
   STARTUP3:    AT V0 M1 Q0 X1 S0=1 S2=255 S7=30 &W0
   REINIT:      AT Z
   DELAY1:      1000
   DELAY2:      1500
   DELAY3:      1500
   DTELOCKED:   y
   ANSWERTYPE:  a
   OPENMODE:    n
   ANSWERCMD:   ATA
   ONHOOK:      ATH0
   OFFHOOK:     ATH1
   ESC_CMDMODE: +++
   ESC_GRDTIME: 1200
   GO_ONLINE:   AT O
   END_OFFHOOK: N
   RC_110:
   RC_150:
   RC_300:      1
   RC_600:
   RC_1200:     5
   RC_2400:     9
   RC_4800:     11
   RC_9600:     12
   RC_19200:
   ERRORCHECK:  y
   ERC_110:
   ERC_150:
   ERC_300:     1R
   ERC_600:
   ERC_1200:    5R
   ERC_2400:    9R
   ERC_4800:    11R
   ERC_9600:    12R
   ERC_19200:

===========================================================================

                               IMPORTANT!

Modem models change very fast. For example, the US Robotics "Dual
Standard" modem we're using is the older modem with v.32 (9600 baud)
capability. The newer "Dual Standard" modems have v.32bis (14400 baud)
capability.

For the fastest possible setup for any modem, once you've filled in your
STARTUPx strings, use Verbose (word) result codes (a V1 anywhere in
your STARTUP strings should turn on verbose result codes). Then:

   VERBOSE_CONNECT: CONNECT
                  (Hayes 9600 baud modems, use VERBOSE_CONNECT: CARRIER)
   YMODEMG: Y

and delete all text lines starting with RC_, ERC_, ERCA_, ERCB_

===========================================================================